Our organization is reckoned as the most prominent suppliers and traders of XBEE Pro S2C 63MW RPSMA S2, XBEE Pro S2C 63MW U.FL S2,XBee 2MW Wire Antenna - Series 2C, Xbee 1mW Wire Antenna - Series 1, Xbee Pro S2c 63mw Wire Antenna S1, Xbee Pro S2c 63mw Wire Antenna S2, XBEE Explorer - Serial And XBEE Explorer USB.All our offered are highly in compliance with the set industrial standards and are stringently tested under well defined parameters before delivering. Clients can avail these modules in desired specifications at market leading prices.
|Operating Frequency||433 MHz|
|Modulation Technique||FSK, GFSK, MSK, GMSK, LORA|
|Packet size||256 Bytes|
The SX1278 transceivers feature the LoRaTM long range modem that provides ultra-long range spread spectrum communication and high interference immunity whilst minimising current consumption. Using Semtech’s patented LoRaTM modulation technique SX1278 can achieve a sensitivity of over -148dBm using a low cost crystal and bill of materials.
The high sensitivity combined with the integrated +20 dBm power amplifier yields industry leading link budget making it optimal for any application requiring range or robustness. LoRaTM also provides significant advantages in both blocking and selectivity over conventional modulation techniques, solving the traditional design compromise between range, interference immunity and energy consumption.These devices also support high performance (G)FSK modes for systems including WMBus, IEEE802.15.4g. The SX1278 deliver exceptional phase noise, selectivity, receiver linearity and IIP3 for significantly lower current consumption than competing devices.
|Minimum Order Quantity||1 Piece|
|Operating Temperature||-40 to 85 DegreeC (industrial)|
|Operating Current (Transmit)||120mA@3.3V,+18dBm|
|Operating Current (Receive)||31mA|
|Indoor/Urban Range||Up to 300 ft. (90 m)|
|Outdoor RF line-of-sight Range||Up to 2 miles (3200 m)|
|Transmit Power Output (maximum)||63mW(+18dBm)|
XBee ZB / ZigBee modules provide cost-effective wireless connectivity to devices in ZigBee mesh networks. Utilizing the ZigBee PRO Feature Set, these modules are interoperable with other ZigBee devices, including devices from other vendors.
The ZB modules requires considerable setup and configuration. XBee Series 1 (802.15.4) and XBee Series 2 (ZB / ZigBee) modules have the same pin-out. However, Series 1 modules cannot communicate with Series 2 modules.
Digi International move both the Series 1 and Series 2 functionality to the S2C hardware. This XBee S2C model is as replacement/upgrade for the XBP24BZ7WIT-004.
|Programmable Output Power||-20 dBm~1 dBm|
|Operation Temperature Range||-40~+85 Deg C|
|Operation Voltage||1.8~3.6 Volts.|
|Distance Range||15 - 30 meter|
|Voltage||5 - 9 V|
|Baud Rates||4800/9600/19200/38400 Hz|
Description: Supporting multiple baud rates of 4800/9600/19200/38400, these Wireless RF CC2500 Transceiver work on ISM band (2. 4 ghz) reserved internationally that do not require any license. These Wireless RF CC2500 Transceiver also support multiple frequencies within same band rate that helps in avoiding data collision with no requirement of complex wireless connection software for connecting to serial devices. Further, these wireless RF CC2500 Transreceiver do not require external antenna and work on 5-9v DC supply with standard uart interface. Suitable for transmitting and receiving data at multiple baud rates, the module is direct line in replacement for serial communication and finds applications for wireless sensor network, wireless device control, wireless data transfer, wireless energy metering, robotics, wireless data logger and others.
|Minimum Order Quantity||1 Piece|
|Operating Temperature||-45 degrees to +85 degrees|
|Operating Voltage||2.7V ~ 3.6V|
|Operating Frequency||2400MHz ~ 2524MHz|
|Transmit power||More than +20 dbm, 50 ohm|
|Receiver sensitivity||-95 dbm|
|Max Emission current||115 mA|
|Max Receive current||45 mA|
NRF24L01P + PA + LNA wireless module core Norway NORDIC company''''s latest high-performance wireless
Digital transmission chip NRF24L01 + with the Division of Professional Design professional full two-way RF power amplifier high power PA and LNA chip, RF switches, bandpass filters, etc., makes effective communication distance greatly expand.
RF part, the Secretary has done a lot of optimization matching debugging, the emission efficiency to achieve the highest harmonic minimum
NRF24L01P + PA + LNA wireless module of RF interference to the external equipment reaches a minimum, while not susceptible to interference from other devices, greatly Uploader High stability of the work.
NRF24L01P + PA + LNA wireless module integration is extremely high, the size of only 41mm x 15.5mm, convenient embed.
|Supply Voltage||1.9V to 3.6V|
|frequency band||2400 - 2483.5 MHz|
|Air data rate||up to 2Mbps.|
|Variable Payload Length||1 to 32 bytes|
|Power Supply||1.9~3.6 V|
|IO port Working Voltage||0~3.3 V / 5 V|
|Transmitting Rate||7 dB|
|Receiving Sensitivity||Less Than -90dB|
|Transmission Range||250 m in open area|
|Data Rate||RF 250 Kbps,Serial up to 1 Mbps|
|Transmit Power||3.1 mW (+5 dBm)|
|Voltage Requirements||2.1 to 3.6 VDC|
|Communication||CMOS UART / SPI @ ~3.3V|
|Dimensions||1.087" L x 0.960" W x 0.16" H (27.61 x 24.38 x 4.06 mm)|
|Operating Temperature Range||-40 to +185 DegreeF (-40 to +85 DegreeC)|
Bee ZB / ZigBee modules provide cost-effective wireless connectivity to devices in ZigBee mesh networks. Utilizing the ZigBee PRO Feature Set, these modules are interoperable with other ZigBee devices, including devices from other vendors. The most common factor in determining whether to use ZB is the potential need to tie-in with other ZigBee-compatible networks or mesh networking. If this is not a requirement, the series 1 802.15.4 modules may be perfectly suitable for your project.
|Supply Voltage||3.3 to 5 V|
|Board Dimensions||52x36x14 mm|
Interfacing Board used to interface ZigBee wireless Module with Desktop or Laptop computer systems.With the aid of our XBEE Explorer USB customers can easily communicate between PC to PC or PC to embedded boards. These Explorer are highly suitable for changing the modules of varied devices using PC through USB port. This Explorer works with all XBee modules including the Series 1 and Series 2.5, standard and Pro version. We have equipped the adapters with five indicator LED''s for depicting the status of the data being received or transmitted, power, signal strength of the recipient and other associated data. As ZigBee communicates through Serial Communication so other end of USB which is connected to PC, treated as COM port for Serial Communication. It is provided with indication LEDs for ease.
|Frequency||ISM 2.4 GHz|
|Data Rates||RF 250 Kbps, Serial up to 1 Mbps|
|Transmit Powers||63 mW (+18 dBm)|
|Indoor or Urban Ranges||300 ft (90 m)|
|Voltage Supply||2.7 to 3.6V|
|Transceiver Chipsets||Silicon Labs EM357 SoC|
|Frequency Band||Ism 2.4 Ghz|
XBee Pro 63mW RPSMA - Series 2C (ZigBee Mesh) is ZigBee RF modules provide cost effective wireless connectivity to electronic devices. They are interoperable with other ZigBee PRO feature set devices. Embedded ZigBee RF modules provide OEMs with a simple way to integrate mesh technology into their application. The XBee-PRO ZigBee RF Modules provide wireless connectivity to end-point devices in ZigBee mesh networks. Using the ZigBee PRO Feature Set, these modules are inter-operable with other ZigBee devices. With the XBee, users can have their ZigBee network up-and-running in a matter of minutes without configuration or additional development.
XBee and XBee-PRO ZigBee modules are ideal for applications in the energy and controls markets where manufacturing efficiencies are critical. The Serial Peripheral Interface (SPI) provides a high-speed interface and optimizes integration with embedded microcontrollers, lowering development costs and reducing time to market. Products in the XBee family require little to no configuration or additional development. Programmable versions of the XBee and XBee-PRO ZigBee module make customizing applications easy. Programming directly on the module eliminates the need for a separate processor. Because the wireless software is isolated, applications can be developed with no risk to RF performance or security.
|Minimum Order Quantity||1 Piece|
|RF Data Rate||250kbps Max|
|Distance Range||1 mile (1600m)|
|Input pins||6 10-bit ADC|
|Digital IO pins||8|
This is the XBee XBP24CZ7WIT-004 module from Digi. The new Series 2C improves upon the power output and data protocol of the Pro Series2. Series 2C modules allow you to create complex mesh networks based on the XBee ZB ZigBee mesh firmware. These modules allow a very reliable and simple communication between microcontrollers, computers, systems, really anything with a serial port! Point to point and multi-point networks are supported.
The XBee/XBee-PRO ZB (S2C) introduces the SPI serial interface to Digis through-hole ZigBee radio. Please refer to the XBee/XBee-PRO ZB (S2C) product manual for more information.