Electronic Motor & ESC

Product Details:

Double BTS7960 43A H-bridge High-Power Stepper Motor Driver Module Arduino for Arduino/Robotics

This driver uses Infineon chips BTS7960 composed of high power drive full H-bridge driver module with thermal over current protection. Double BTS 7960 H-bridge driver circuit, with a strong drive and braking, effectively isolating the microcontroller and motor driver! High current 43A.

Features of Double BTS7960 43A H-bridge High-Power Stepper Motor Driver Module:

• Double BTS7960 large current (43A) H-Bridge motor driver.
• 5v isolate with MCU, and effectively protect MCU.
• Can solder heat sink.

Applications of Double BTS7960 43A H-bridge High-Power Stepper Motor Driver Module:

• DIY projects.
• Robotics projects.
• Arduino projects.
• Raspberry-Pi projects.
• Electrical/Electronic projects.

Get best price of Stepper Motor Driver Module for Rs 342/-

Product Details:

TB6600 stepper motor driver provides maximum 4.5A output current. TB6600 comes with output sort-circuit protection, Low-Pressure shut-off, Overheating parking and over-current protection. Output current is infinitely adjustable to meet various applications. Features:

• High current, high voltage TB6600HG new original chip, there are low-pressure shut-off, overheating parking and over-current protection circuit, short-circuit protection and increased compared to TB6560
• High-speed optical coupling 6N137, ensure high speed without losing step
• The output current is infinitely adjustable to meet various application requirements
• Automatic half current function. And a semi-automatic flow switch, easy to use
• The use of high-speed optical coupling 6N137 ensure high-speed without losing step
• Printed on the back panel are subdivided setup instructions
• Used to increase the heat sink, good heat dissipation
• Output short-circuit protection
• Using common anode input mode, there are two input terminals, wiring more convenient

 

Product Details:

ESP12E Motor Shield is a high-current motor drive module compatible with ESP12E Dev Kit and . The module is designed with a plug-in board and can be directly connected to the ESP12E Dev Kit or NodeMCU Lua module.

The module adopts the excellent high-power motor dedicated full-bridge chip L293DD produced by STMicroelectronics. It can directly drive 2 DC motors or 1 stepping motor, and the driving current can reach 1.2A. The layout of the circuit diagram is reasonable, the package is packaged and the installation is very convenient.

The module uses the IO port of the ESP12E Dev Kit as the control port, and the internal logic chip completes the motor IC drive. Therefore, it only occupies four ports of the control boards D1, D2, D3, and D4, which are respectively used as PWMA (motor A speed) and PWMB (motor B). Speed), DA (Motor A direction), DB (Motor B direction) function.

The module also draws multiple pins such as VIN, 3.3V, DIO, AIO, SDIO, UART, SPI, RST, EN, etc., which can be easily connected to various sensors (temperature and humidity, buzzer, illumination, relay, etc.).

The module adopts a user-friendly design scheme, and the power button switch allows the user to conveniently switch the power.

This module can be used directly to control smart cars.

 

Product Details:

This hardware, with the SimonK firmware, gives you the perfect solution for multirotor use.

Highest efficiency 100% N-FET design.
Highest accuracy with crystal oscillator (Temperature won't affect the PWM operating range like other cheap ESC's).

• No low voltage cutoff, because any cutoff in a multirotor = crash.
• No over temp cutoff, because any cutoff in a multirotor = crash.
• Super high refresh rate, no buffering of the input signal, resulting in more than 490Hz response rate.
• 16KHz motor frequency, giving fastest response of the motor, and quietest operation as well (no 8KHz squeal).
• Super simple, foolproof operation. Nothing to program other than the throttle range

Product Details:

• 1400KV UAV brushless motor
• Ideal to work with 30A ESC
• Efficiency current (maximum): 6-12A (>75%)
• Current (no load): 0.7A

The UAV Brushless Motor A2212/10 1400Kv provides excellent performance, quality, and dependability at an affordable price. Manufactured with high quality bearings and components, this brushless motor is one of the smoothest and most powerful in its class. Each motor is pre-solderd with 3.5mm male gold bullet connectors and includes an accessory pack with collet-style prop adapter, X-mount plate and matching set of female 3.5mm bullet connectors

Additional Information:

• Item Code: A2212

Product Details:

D2826 is a brushless motor with KV ratting of 1100 to 1800. Brushless motors are synchronous motors which are powered by a DC electric source via an integrated inverter/switching power supply, which produces an AC electric signal to drive the motor. In this context, AC, alternating current, does not imply a sinusoidal waveform, but rather a bi-directional current with no restriction on waveform. Note: D2826 1100kv to 1800kV is a Short shaft BLDC motor.

Additional Information:

• Item Code: DN2826-1400kv-1800kv
• Delivery Time: 8-10 days