GY Series Modules

Product Details:

Sensors:

• MPU6050 3x Axis accelerometer sensor and 3x Axis gyroscope sensor
• HMC5883L Triple Axis Magnetometer
• BMP180 Barometric Pressure Sensor

Specifications:

• Build in ultra low noise linear LDO voltage regulator
• Build-in on board filters, which reduce noise from motor and other high current electronics
• All sensors connected to I2C bus
• You can easily select two I2C address for MPU6050 by soldered jumper
• Power LED
• Build in Logic level converter for I2C
• Dimensions 20x16mm
• Designed for 5V logic level

Applications:

• FPV, RC and Robots systems
• GPS navigation systems
• Impact recognition and logging
• Gaming and virtual reality input devices
• Motion-activated functions
• Intelligent power saving for handheld devices
• Vibration monitoring and compensation
• Free-fall detection
• 6D-orientation detection

Additional Information:

• Item Code: gy-87
• Delivery Time: 8 - 10 days

Product Details:

Description:

• Name: ADXL335 module (triaxial accelerometer analog output)
• Analog X, Y, Z three-axis output Direct output angle code

Additional Information:

• Item Code: ADXL335
• Delivery Time: 8 - 10 days

Product Details:

The ADXL345 is a small, thin, low -power three-axis accelerometer, can be high Up to ± 16 g acceleration with high resolution (13) measurements. Digital Outputs According to 16-bit two's complement format, Or I2C digital interface can be accessed through the SPI (3 -wire or 4-wire) .ADXL345 is well suited for mobile device applications. It can tilt sensing applications measuring the static acceleration of gravity, you can also measure the dynamic increase resulting from motion or shock Speed. It has a high resolution (4 mg / LSB), capable of measuring the tilt of about 0.25 °Angle change. Use the accelerometer ADXL345 digital output, etc., without the need for Analog to digital conversion, thus saving system cost and board area. In addition, The ADXL345 is a small, thin, ultra-low -power 3-axis accelerometer, resolution High (13) , measuring range up to ± 16g. The digital output data is 16 -bit binary Complement format, or I2C digital interface can be accessed through the SPI (3 -wire or 4-wire).ADXL345 is well suited for mobile device applications. It can tilt sensing applications measuring the static acceleration of gravity, can also measure the impact caused by movement or Action State acceleration. Its high resolution (3.9mg/LSB), capable of measuring less than 1.0 ° the inclination angle.

The device offers a variety of special detection. Active and inactive detection through Comparing arbitrary axis acceleration threshold set by the user to detect the presence of transport Action to occur. Tapping any direction detection function detects single and dual vibration Made. Freefall detection function can detect whether the device is dropped. These Function can be independently mapped to two interrupt output pin one. Being Shen Please patented integrated memory management system uses a 32 FIFO (FIFO) buffer can be used to store data to the host processor load Minimize and reduce overall system power consumption. Motion -based low-power mode supports intelligent power management, which at very low Power consumption threshold sensing and active acceleration measurement .ADXL345 uses 3 mm × 5 mm × 1 mm, 14 -pin mini ultra-thin plastic

Technical parameters:

• Name : ADXL345 module ( triaxial acceleration of gravity )
• Use Chip : ADXL345
• Measuring range : ± 2g ± 16g
• 3-axis , ± 2g / ± 4g / ± 8g / ± 16g

Product Details:

HMC5883L 3V-5V Triple Axis Compass Magnetometer Sensor Module

Specifications:

• Immersion Gold PCB, machine welding process to ensure quality.
• Name: HMC5883L module (three-axis magnetic field module).
• Communication modes: standard IIC communication protocol.

Note: Pictures shown above are just for representational purpose, and the actual layout, size, manufacturer, schematics, etc. may differ based on the stock available at that moment.

Product Details:

BMP180 Barometric Pressure Sensor Module

Features:

• Measuring the absolute pressure of the environment using a digital barometer such as this has some interesting applications. By converting the pressure measured into altitude, you have a reliable sensor for determining the height of your robot, plane or projectile!
• Using a sensor as capable as the BMP180 you can achieve accuracy of 1m, with noise of only 17cm in ultra high resolution noise.
• The device will operate at only 0.3uA meaning low current draw for battery powered applications.
• The BMP180 comes fully calibrated and ready to use.
• As the device operates over I2C we've added optional I2C pull ups that can be enabled using the PU (pull up) jumper on the board for your convenience and ease during breadboarding.
• Using I2C, the device provides pressure and temperature as 16bit values, which are used along with calibration data within the device to provide a temperature compensated altitude calculation.

Additional Information:

• Item Code: GY-68-BMP180
• Delivery Time: 8 - 10 days

Product Details:

This module is a digital ambient light sensor, IIC I2C communication. Good for arduino light detection

• Wide range and High resolution. ( 1 - 65535 lx )
• Power Supply 3V-5V
• 16bit AD converter built-in
• Low Current by power down function * 50Hz / 60Hz Light noise reject-function
• Light source dependency is little. ( ex. Incandescent Lamp. Fluorescent Lamp. Halogen Lamp. White LED. Sun Light )
• Small measurement variation ( /- 20%)

Features:

• Digital Light intensity detection module: GY-30 Chip : BH1750FVI
• Power supply: 3V-5V power
• Light range 0-65535 lx
• Sensor built-in : 16 bitAD converter
• Direct digital output, bypassing the complex calculation, bypassing the calibration
• Don''''t distinguish between ambient light
• Close to the spectral characteristics of visual acuity
• widely use to 1-lux high precision measurement
• Standard NXP I2C communication agreement

Product Details:

MLX90614ESF-BAA-000-TU-ND is an infrared thermometer for non-contact temperature measurements. It can use with any microcontroller that can communicate with it through it''s I2C interface.

Features:

• Easy to integrate
• Mounted on a breakout board with two types of pins
• 10k Pull up resistors for the I2C interface with optional solder jumpers
• Factory calibrated in temperature range:
  • -40+125°C for sensor temperature
  • -70+380°C for object temperature
• High accuracy of 0.5°C over wide temperature range (+50°C for both) High (medical) accuracy calibration
• Measurement resolution of 0.02°C
• Single and dual zone versions
• SMBus compatible digital interface
• Customizable PWM output for continuousreading
• Different package options for applications and measurements versatility

Applications:

• High precision non-contact temperature measurements
• Automotive blind angle detection
• Multiple zone temperature control – up to 127sensors
• Thermal relay / alert
• Movement detection
• Livestock monitoring
• Body temperature measurement

Additional Information:

• Item Code: GY-906MLX90614ESF
• Delivery Time: 8 - 10 days

Product Details:

Specifications:

• On-board MPU - 6050 integrated 6 axis motion processing chip.
• On-board LDO chip, support 5V / 3.3V voltage input.
• Commonly used pin have eduction, pin have standard 2.54 mm spacing.
• Module support IIC standard communication protocol for easy interfacing.
• 16 bit AD converter that can generate 16 bits of data output.
• Users can control the accelerator sensor range within 2g, 4g, 8g and 16g.
• Angular velocity, Sensing range: 250 500 1000 and 2000 / SEC (DPS)

Product Details:

Bosch has stepped up their game with their new BMP280 sensor, an environmental sensor with temperature, barometric pressure that is the next generation upgrade to the BMP085/BMP180/BMP183. This sensor is great for all sorts of weather sensing and can even be used in both I2C and SPI! This precision sensor from Bosch is the best low-cost, precision sensing solution for measuring barometric pressure with ±1 hPa absolute accuracy, and temperature with ±1.0°C accuracy. Because pressure changes with altitude, and the pressure measurements are so good, you can also use it as an altimeter with ±1 meter accuracy Enhancement of GPS navigation(e.g.time-to-first-fix improvement,dead-reckoning,slope detection) Indoor navigation(floor detection,elevator detection) Outdoor navigation,leisure and sports applications Weather forecast Health care application(e.g. sirometry) Vertical velocity indication(e.g. risk/sink speed)

Additional Information:

• Packaging Details: 1 x GY-BMP280-3.3 High Precision Atmospheric Pressure Sensor Module