Product Details:
Minimum Order Quantity | 1 Piece |
Jumpers | A26228-ND |
Design | Compact |
Voltage | 12-36 VDC |
Screw Terminal | 5 mm (A97996-ND) |
Material | CNC |
Packaging Type | Box |
The CNC Shield makes it easy to get your CNC projects up and running in a few hours. It uses opensource firmware on Arduino to control 4 stepper motors using 4 A4988 Stepper drivers,, with this shield and the Arduino you can build all kinds of robotics or CNC projects including CNC routers,laser cutters and even pick&place machines.
Features:
Product Details:
Minimum Order Quantity | 1 Piece |
Maximum Logic Voltage | 5.25 V |
Dimensions | 20.4x15.6 mm |
Minimum Operating Voltage | 8.2 V |
Continuous Current Per Phase | 1.5 Amp |
Minimum Logic Voltage | 2.5 V |
Microstep Resolutions | Full,1/2,1/4,1/8,1/16 and 1/32 |
Maximum Operating Voltage | 45 V |
Maximum Current Per Phase | 2.2 Amp |
This breakout board for TI’s DRV8825 microstepping bipolar stepper motor driver features adjustable current limiting, over-current and over-temperature protection, and six microstep resolutions (down to 1/32-step). It operates from 8.2 V to 45 V and can deliver up to approximately 1.5 A per phase without a heat sink or forced air flow (rated for up to 2.2 A per coil with sufficient additional cooling). The driver has a pinout and interface that are nearly identical to those of A4988 stepper motor driver carriers, so it can be used as a higher-performance drop-in replacement for those boards in many applications.
Product Details:
Minimum Order Quantity | 1 Piece |
Input Supply Voltage (VDC) | 5 |
Length (mm) | 93 |
Width (mm) | 87 |
Screen size | 128x64 |
Height (mm) | 14 |
Package includes | SD-Card reader, an rotary encoder and a 128 x 64 dot matrix LCD display |
Cable Length (cm) | 30 |
Additional Information:
Product Details:
Model Name/Number | A4988 |
Motor Voltage | 8 to 35 V DC |
Usage/Application | CNC |
Microstep resolutions | Full,1/2,1/4,1/8,and 1/16 |
Continuous current per phase | 1 amp |
Maximum current per phase | 2 Amp |
Minimum logic voltage | 3V |
Maximum logic voltage | 5.5 V |
The A4988 stepper motor driver carrier is a breakout board for Allegro’s A4988 microstepping bipolar stepper motor driver. The driver features adjustable current limiting, overcurrent and overtemperature protection, and five different microstep resolutions (down to 1/16-step). It operates from 8 – 35 V and can deliver up to approximately 1 A per phase without a heat sink or forced air flow (it is rated for 2 A per coil with sufficient additional cooling).
Product Details:
Model Name/Number | RAMPS 1.6 |
Material | Polyamide (PLA) |
Support | A4988 DRV8825 and other motor drivers |
Size | About 101.5 x 60.5 mm |
Power | 270 W |
Voltage | 12 V |
Additional Information:
Product Details:
Minimum Order Quantity | 1 Piece |
Supply Voltage | 12 V |
Length | 100 mm |
Width | 60 mm |
Height | 26 mm |
Weight | 60 gm |
Current | 5 A |
The RAMPS (RepRap Arduino Mega Shield) is an all-in-one design to fit the necessary components for a 3D printer into one plug in shield for an Arduino MEGA. The plug in shield design includes plug in stepper drivers and extruder control electronics sockets for easy service, part replacement, upgrade-ability and expansion. Additionally, a number of Arduino expansion boards can be added to the system as long as the main RAMPS board is kept to the top of the stack. Ramps boards are the heart of most DIY 3D printers on the market and a nice clean compact way to integrate all the systems into a compact enclosure mountable format.
Features:
Product Details:
Speed | 4500RPM+-10% |
Power Source | Electric Blower |
Noise Level | 33.84dba+-10% |
Airflow | 9.17 CFM |
Rated Current | 70 mA |
Fan dimension | 40x40x20mm |
Voltage | 12V DC |
Bearing Type | Sleeve Bearing |
Net Weight | 26 g/pc |
Suitable for | 3D printer Z Axis. |
Wire Length | 30 cm |
Product Details:
Color | Red |
Size | 1.6 x 4 cm |
Voltage | 300 V |
Current | 2 A |
Temperature resistance | 80 degree centigrade |
Additional Information:
Product Details:
Size/Dimension | Available 5 to 5 mm & 5 to 8 mm |
Made of | Machined Aluminum |
Measures | 1" x 0.7" diameter / 25mm x 18mm diameter |
Weight | 15 grams |
Applications | Shaft coupler Often used to connect servo motor, stepper motor, encoder, screw driving, machine plat |
Inner diameter | 5 mm |
Product Details:
Minimum Order Quantity | 1 Piece |
Resistance | 100k Ohm |
Temperature Coefficient | NTC |
Nominal value | R25 (25 Degree C) |
Resistance precision | +- 1%, +- 2%, +- 3% |
B value accuracy | +- 1% |
This is Thermistor 100k NTC with 1 Meter Cable Temperature Sensor for 3D Printer Reprap. The thermistor is a thermally sensitive resistor known for exhibiting a large change in resistance with only a small change in temperature.
The thermistor comes with copper tip, make the temperature control more accurately, it will have a better thermal transfer and solve the problem for thermistor fixed unstable and the problem of easy damageAdditional Information:
Product Details:
Minimum Order Quantity | 1 Piece |
Lead Screw Material | 304 Stainless Steel |
Screw Type | 4 start |
Length of Bolt | 500mm |
Bolt Body Diameter | 8mm |
Brass Nut Size (Dia. x Height) | 22 x 15 mm |
Weight | 170 mm |
The 500mm Trapezoidal 4 Start Lead Screw 8mm Thread 2mm Pitch Lead Screw with Copper Nut used for general machine tools such as 3D printing.
It has good wear resistance and strength, high accuracy, hard to rust and has good performances due to low friction coefficients and long usage spans. This Trapezoidal Lead Screw with Copper Nut is a new type of screw that is mainly used in stepper motor, machine tool rails and other types of equipment.
To know more about the pitch, please refer to the schematic below.
Features :
4 Start Lead Screw
Mainly use for Stepping motor driving guide rail.
T shape design, made of high-quality stainless steel material.
Easy to install and convenient to use.
Fine producing and practical.
Specifications:
Lead Screw Material: 304 Stainless Steel.
Screw Type: 4 Start
Length of Bolt (mm): 500
Bolt Body Diameter (mm): 8
Brass Nut Size (Dia. x Height) mm: 22 x 15
Weight(gm): 170
Shipment Weight: 0.2 kg
Shipment Dimensions: 53 × 3 × 3 cm
Additional Information:
Product Details:
Minimum Order Quantity | 1 Piece |
Weight | 136gm |
Lead Screw Material | 304 Stainless Steel |
Screw Type | 4 start |
Length of Bolt | 400mm |
Bolt Body Diameter | 8mm |
Brass Nut Size (Dia. x Height) | 22 x 13 mm |
The 400mm Trapezoidal 4 Start Lead Screw 8mm Thread 2mm Pitch Lead Screw with Copper Nut used for general machine tools such as 3D printing.
It has good wear resistance and strength, high accuracy, hard to rust and has good performances due to low friction coefficients and long usage spans. This Trapezoidal Lead Screw with Copper Nut is a new type of screw that is mainly used in stepper motor, machine tool rails and other types of equipment.
To know more about the pitch, please refer to the schematic below.
Features :
4 Start Lead Screw
Mainly use for Stepping motor driving guide rail.
T shape design, made of high-quality stainless steel material.
Easy to install and convenient to use.
Fine producing and practical.
Specifications:
Lead Screw Material: 304 Stainless Steel.
Screw Type: 4 Start
Length of Bolt (mm): 400
Bolt Body Diameter (mm): 8
Brass Nut Size (Dia. x Height) mm: 22 x 13
Weight(gm): 136
Shipment Weight: 0.15 kg
Shipment Dimensions: 41 × 3 × 3 cm
Additional Information:
Product Details:
Minimum Order Quantity | 1 Piece |
Material | Neoprene Rubber With Fiberglass Core |
Shape | Open Loop |
Pitch | 2mm |
Belt length | 106cm |
Width | 6mm |
Belt Height | 1.52mm |
Highest quality precision GT2 Width 6mm Black Open ended with steel wire Timing Belt For 3D Printer. Made from NEOPRENE Synthetic Rubber reinforced with fiberglass cords for superior strength. Neoprene an oil-resistant substitute for natural rubber, was invented by DuPont scientists on April 17, 1930.
Features:
Additional Information:
Product Details:
Minimum Order Quantity | 1 Piece |
Usage/Application | Industrial |
Shape | Round |
Material | Brass |
Packaging Type | Box |
Lead | 8mm |
Suitable for | 3D printer Z Axis |
Pitch | 2mm |
Lead Screw Diameter | 8mm |
Additional Information:
Product Details:
Power | 40 W |
Voltage | 12 V and 24 V (Available in both Voltage) |
Wire Length | 1 m |
Cartridge Length | 2.3 cm |
Cartridge Diameter | 6 mm |
Application | All modern printers use cartridge heaters |
Product Details:
Display Type | LCD |
Supply Voltage | 5 V |
Cable Length | 30 cm |
Length | 150 mm |
Number of Character | 20 Character |
Height | 24 mm |
Number of Line | 4 Line |
Version | RAMPS 1.4 |
Width | 64 mm |
The intelligent controller includes an SD card reader, rotary encoders and a 20-character × 4 line LCD display. You can easily connect it to your RAMPS 1.4 board using "smart adapter" included.
This panel connect your RAMPS 1.4, you do not need your computer, your SD card intelligent controller power supply. All further operations, such as calibration, the axis movement can be done only with a rotary encoder intelligent controller. 3D design print without a computer, just use the G code design stored on the SD card.
Features:
Product Details:
Minimum Order Quantity | 1 Piece |
Usage/Application | Used on 3D printers and CNC machines |
Pitch | 26 x 30 mm |
Material | Metal, Rubber |
Model Name/Number | SCS8UU, SCS10UU, SCS12UU |
Screw Hole Dia(Each) | 4 mm |
Inner Diameter | 8, 10, 12 mm |
Additional Information:
Product Details:
Minimum Order Quantity | 1 Piece |
Cable Length (cm) | 70 |
Operating Voltage (VDC) | 300 |
Max. Operating Current (mA) | 2A |
Temperature Resistance(C) | 80 |
CNC 3D Printer Mech Endstop Switch uses a lever switch to detect when it is activated. The switch is wired up so that when activated, it pulls the signal to LOW. There is also an LED on the board that will light up when the switch is activated. It uses a standard 4 pin 100 pitch header and accepts a standard, old-style CD-ROM audio connector cable.
The mechanical endstop is a simple solution to a simple problem. We want to be able to detect when an X/Y/Z stage has reached its minimum or maximum. Instead of messing with flags or complicated light beam interruption, we use a mechanical switch.
If we place the switch in the path of the stage, then the stage itself will simply close the switch when it moves against it. Other than properly positioning the switch, we do not need to modify the stage at all.
Additional Information:
Product Details:
Minimum Order Quantity | 1 piece |
Material | ABS or PLA |
Application | Bridge the gap between experienced and novice users |
Power Adapter | 12V 3A |
LEDs | 2 Nos. ( Power LED & Working LED) |
Speed | Unique speed control switch |
Temperature Control | Adjustable LED screen to control the temperature |
Product Details:
Minimum Order Quantity | 1 Piece |
Part Type | Heated Bed PCB |
Printer Type | 3 D printer |
Color | Red |
Resistance between | 1.0 and 1.2 ohm |
Size | 214mmx 214mm |
Etching | 35 um copper |
Dimensions | 214mmx 214mm |
Model Number | MK2B |
Power Input | 12V or 24v |
Product Details:
Minimum Order Quantity | 1 Piece |
File Format Supported | STL, OBJ, G-Code |
Layer Thickness | 0.1-0.4mm |
Printing Precision | +-0.1mm |
Nozzle Diameter | 0.4mm eom |
Printing Size | 220*220*250mm |
Input | AC 100-265V 50-60Hz |
Package weight | 8kg |
Working Mode | Online or SD ofline |
Machine Size | 440*410*465mm |
Max Nozzle Temperature | 255 Degree C |
Fliament | 1.75mm PLA,TPU,ABS |
Modeling Technology | FDM(Fused Deposition Modeling) |
Max Hot bed Temperature | 110 Degree C |
Output | DC 24V 15A 360W |
Max Traveling Speed | 180mm/s |
Additional Information:
Product Details:
Lead Screw Material | 304 Stainless Steel |
Screw Type | 4 start |
Length of Bolt | 300mm |
Bolt Body Diameter | 8mm |
Brass Nut Size | (Dia. x Height) : 22 x 13 mm |
Weight | 100gm |
The 300mm Trapezoidal 4 Start Lead Screw 8mm Thread 2mm Pitch Lead Screw with Copper Nut used for general machine tools such as 3D printing.
It has good wear resistance and strength, high accuracy, hard to rust and has good performances due to low friction coefficients and long usage spans. This Trapezoidal Lead Screw with Copper Nut is a new type of screw that is mainly used in stepper motor, machine tool rails and other types of equipment.
To know more about the pitch, please refer to the schematic below.
Features :
4 Start Lead Screw
Mainly use for Stepping motor driving guide rail.
T shape design, made of high-quality stainless steel material.
Easy to install and convenient to use.
Fine producing and practical.
Specifications:
Lead Screw Material: 304 Stainless Steel.
Screw Type: 4 Start
Length of Bolt (mm): 300
Bolt Body Diameter (mm): 8
Brass Nut Size (Dia. x Height) mm: 22 x 13
Weight(gm): 100
Shipment Weight: 0.11 kg
Shipment Dimensions: 31 × 3 × 3 cm
Additional Information:
Product Details:
Minimum Order Quantity | 1 Piece |
Button head | 4 x 8mm long M3 |
CSK head | 4 x 10mm long M3 |
Nut | 4 x M3 |
Part number | NEMA17 |
You have a stepper motor, but you need to attach it to your CNC project, eh? Not so easy if you don't have a stepper motor mount just like this fine one one here! This mount will fit any NEMA-17 motor (with 31mm hole spacing) with four screws. There's two 30mm long slots, 30mm apart so you can easily attach it. Made of steel with welded 90-degree support triangles, its got a solid construction The bracket features several slots and holes for a wide variety of mounting solutions, and four M3×6mm screws are included for securing the motor to the bracket.
This lightweight but strong bracket is made from 3mm-thick black anodized aluminum and is specifically designed to work with the typical faceplate mounting holes of NEMA 17 stepper motors. The slots through which the motor mounts comes with holes at the right places to mount a NEMA 17 Stepper Motor. The other side of the bracket includes a variety of slots and holes that can be used with #6, #8 and M4 screws
Additional Information:
Product Details:
Minimum Order Quantity | 1 Piece |
Length | 45mm |
Outer Casing | Chromium Steel |
Outer Diameter(mm) | 15 |
Shaft ID(mm) | 8 |
Weight (gm) | 24 |
This LM8LUU 8mm Bushing Longer Linear Ball Bearing is a longer version of our standard LM8LUU linear slide bush for 8mm hardened steel shafts.
The Bearings gives you very precise, safe and reliable linear motion system. Such linear motion bearings are mostly used in 3D printers and CNC(Computer Numerical Control) machines. This Linear Ball Bearing can provide low friction motion along a single axis, hence find a wide range of applications in DIY and robotics prototyping.
This LM8LUU 8mm Bushing Longer Linear Ball Bearing closed type ball bushing has an 8mm bore and 15mm outer diameter is suitable for use in a mounted slide unit to carry components.
Balls in the cage loop run along a smooth ball guide surface to ensure low noise even in the high-speed operation.
Since Linear Motion bearings slide along the round shaft, for the reliable and smooth motion the shaft must be lubricated. The quality of the shaft directly influences the quality of linear motion we get. So, using chrome plated and hardened shaft may serve beneficial.
The linear motion bearings is available in more varieties as below
LM6LUU
LM10LUU
LM12LUU
LM16LUU
Additional Information: