Boards & Shields Compatible With Arduino

Product Details:

Specification:

• 14 Digital input / output port: RX, TX, D2 - D13
• 8 analog inputs: A0 - A7
• 1 pairs of ports TTL level serial transceiver: RX / TX
• 6 PWM ports: D3, D5, D6, D9, D10, D11
• Using Atmel AtMega328P-AU MCU
• Support serial download
• Support for external 3.3V - 12V DC power supply
• Support 9V battery supply
• Clock frequency: 16MHz
• Size: 33.3 x 18.0mm

Additional Information:

• Item Code: Arduino-Compatible-PRO-MINI-5V-16M
• Delivery Time: 8 - 10 days

Product Details:

The D1 R2 is a WiFi capable ESP8266EX based development board in the form of the common Arduino UNO board format. This board is compatible with the Arduino IDE and with NodeMCU. The D1 R2 also features an on-board switching power supply which allows you to power the board from a power supply up to 12V.

Note: The D1 R2 is a 3.3V device. If you connect it to 5V digital sensors or devices you will need a logic level converter.

Specifications:

• On-Board Switching Power Supply
• Input Voltage Range: 9V to 12V

Product Details:

The Digispark is an Attiny85 based microcontroller development board similar to the Arduino line, only cheaper, smaller, and a bit less powerful. With a whole host of shields to extend its functionality and the ability to use the familiar Arduino IDE the Digispark is a great way to jump into electronics, or perfect for when an Arduino is too big or too much.

Product Description

• Brand new and high quality.
• Support for the Arduino IDE 1.0+ (OSX/Win/Linux).
• Power via USB or External Source - 5v or 7-35v (automatic selection).
• On-board 500ma 5V Regulator.
• Built-in USB (and serial debugging).
• 6 I/O Pins (2 are used for USB only if your program actively communicates over USB, otherwise you can use all 6 even if you are programming via USB).
• 8k Flash Memory (about 6k after bootloader).
• I2C and SPI (vis USI).
• PWM on 3 pins (more possible with Software PWM).
• ADC on 4 pins.
• Power LED and Test/Status LED (on Pin0).

Product Details:

This is STM32F103C8T6 Minimum System Board Microcomputer STM32 ARM Core Board. This board is a low-cost Minimum System Development Board for ARM Microcontroller STM32F103C8T6.

Board is suitable for learners that want to learn STM32 microcontroller with ARM Cortex-M3 32-bit core.


Features:

• 100% Brand new and high-quality STM32 Board

• 72MHz work frequency.
• 64K flash memory, 20K SRAM.
• 2.0-3.6V power, I/O.
• Reset(POR/PDR).
• 4-16MHz crystal.

• Onboard Mini USB interface, you can give the board power supply and USB communication.

Additional Information:

• Item Code: STM32F103C8T6

Product Details:

Features:

• 2.4 inch LCD TFT display
• Bright, 4 white-LED backlight, on by default but you can connect the transistor to a digital pin for backlight control
• Colorful, 18-bit 262,000 different shades
• 4-wire resistive touchscreen
• 240 x 320 resolution
• Spfd5408 controller with built in video RAM buffer
• 8 bit digital interface, plus 4 control lines
• Uses digital pins 5-13 and analog 0-3. That means you can use digital pins 2, 3 and analog 4 and 5. Pin 12 is available if not using the micro SD
• 5V compatible, use with 3.3V or 5V logic

Package included:

1 x 2.4 inch TFT LCD Shield

Additional Information:

• Item Code: 2.4-TFT
• Delivery Time: 8 - 10 days

Product Details:

This is a 16x2 LCD and Keypad shield for Arduino Uno, Diecimila, Duemilanove and Freeduino boards. to provide a user-friendly interface that allows users to go through the menu, make selections etc. It consists of a 1602 white character blue backlight LCD. The keypad consists of 5 keys — select, up, right, down, left and reset. To save the digital IO pins, the keypad interface uses only one ADC channel. The key value is read through a 5 stage voltage divider.

Product Details:

Details:

• Our product is highly appreciated by our customers all over the india for the quality we offers.

Product Details:

Specification:

• With this Ethernet Shield, your Arduino board can be used to connect to internet.
• Can be used as server or client.
• Directly plug puzzle board, no soldering required.
• Controller: W5100.
• This is the latest version of the Ethernet Shield.
• This Arduino Ethernet Shield which is based on the Wiznet W5100 Ethernet Chip gives you an easy way to get your Arduino Online.
• It is directly supported by Arduino official Ethernet Library.
• It adds a micro-SD card slot, which can be used to store files for serving over the network.
• It is compatible with the Arduino Duemilanove (168 or 328), Uno as well as Mega (1280/2560) and can be accessed using the SD library.
• The Wiznet W5100 provides a network (IP) stack capable of both TCP and UDP.
• It supports up to four simultaneous socket connections.
• Use the Ethernet library to write sketches which connect to the internet using the shield.
• Fits all version of Arduino Main board,2009,UNO, mega 1280, mega 2560.
• Size: 7cm x 5.4cm x 2.4cm - 2.76inch x 2.12inch x 0.94inch.
• MAC address: 0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xED byte mac[] = { 0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xED }

Additional Information:

• Item Code: W5100
• Delivery Time: 8 - 10 days

Product Details:

The Digispark is an Attiny85 based microcontroller development board similar to the Arduino line, only cheaper, smaller, and a bit less powerful. With a whole host of shields to extend its functionality and the ability to use the familiar Arduino IDE the Digispark is a great way to jump into electronics, or perfect for when an Arduino is too big or too much.

The Digispark is shipped fully assembled except for the two included and easy to solder headers.

Product Sepcifications

• Support for the Arduino IDE 1.0+ (OSX/Win/Linux)
• Power via USB or External Source - 5v or 7-35v (12v or less recommended, automatic selection)
• On-board 500ma 5V Regulator
• Built-in USB
• 6 I/O Pins (2 are used for USB only if your program actively communicates over USB, otherwise you can use all 6 even if you are programming via USB)
• 8k Flash Memory (about 6k after bootloader)
• I2C and SPI (vis USI)
• PWM on 3 pins (more possible with Software PWM)
• ADC on 4 pins
• Power LED and Test/Status LED

Product Details:

The USB Host Shield contains all of the digital logic and analog circuit necessary to implement a full-speed USB peripheral/host controller with Arduino. User can use the Arduino to connect and control any USB slave device easily.

Features

• USB 2.0 Full Speed compatible
• 3.3/5V operation level compatible
• All GPIOx pins break-out
• USB Host 5V/500mA supply for USB protocol

Additional Information:

• Item Code: USB-Host-Shield
• Delivery Time: 8 - 10 days

Product Details:

This Arduino compatible motor Driver shield is a full-featured products that it can be used to drive 4 DC motors or two 4-wire stepper and two 5V ''hobby'' servo. It drive the DC motor and stepper with the L293D, and it drive the servo with Arduino''s pin9 and pin10.

Features:

• 2 x L293D Motor Control Chips
• Total of 4 H-Bridges for controlling 4 DC motors or 2 Stepper motors
• 2 x Server ports for controlling RC Hobby Servos
• The logic control voltage Vss: 4.5~5.5V
• Motor Supply Voltage: 4.5 ~ 12V
• Reduced control pins needed through 8-stage serial shift registers
• Drive part of the operating current Io: 1.2A (0.6A per bridge)
• External power connection via a screw-terminal block
• Screw-Terminal blocks for connection to motors

Additional Information:

• Item Code: l293D
• Delivery Time: 8 - 10 days

Product Details:

The APPC220 Bluetooth Voice Recognition Module has a wide range of features which makes it perfect for beginners who want to study. It can be useful for advanced users because it has built-in general purpose components:

Additional Information:

• Item Code: APPC220

Product Details:

Features:

• SD card interface works with FAT16 or FAT32 formatted cards.
• 3.3V level shifter circuitry prevents damage to your SD card.
• Real time clock (RTC) keeps the time going even when the Arduino is unplugged.
• Included libraries and example code for both SD and RTC, means you can get going quickly.
• Prototyping area for soldering connectors, circuitry or sensors.
• Onboard 3.3V regulator is both a reliable reference voltage and also reliably runs SD cards that require a lot of power to run.
• Works with Arduino UNO, Duemilanove, Diecimila, Leonardo or ADK/Mega R3 or higher.
• ADK/Mega R2 or lower are not supported.

Product Details:

The Pro Micro is similar to the Pro Mini except with an ATmega32U4 on board. The USB transceiver inside the 32U4 allows us to add USB connectivity on-board and do away with bulky external USB interface.

This tiny little board does all of the neat-o Arduino tricks that you’re familiar with: 4 channels of 10-bit ADC, 5 PWM pins, 12 DIOs as well as hardware serial connections Rx and Tx. Running at 16MHz and 5V, this board will remind you a lot of your other favorite Arduino-compatible boards but this little guy can go just about anywhere. There is a voltage regulator on board so it can accept voltage up to 12VDC. If you’re supplying unregulated power to the board, be sure to connect to the “RAW” pin on not VCC.

Features:

• Supported under Arduino IDE v1.0.1
• On-Board micro-USB connector for programming
• 4 x 10-bit ADC pins
• 12 x Digital I/Os (5 are PWM capable)
• Rx and Tx Hardware Serial Connections
• Our Smallest Arduino-Compatible Board Yet!

Product Details:

The development board is based on the WiFi-SoC ESP8266 and is made for fast Internet-of-Things (IoT) prototyping. It is flashed with the NodeMCU firmware and can be set up and programmed right away with the on-board microUSB connection. With only few lines of code the NodeMCU Dev Kit is connected to your local network and ready to be controlled by other network members like computers and smartphones. The D1 mini is a mini wifi board based on ESP-8266EX. Features: -11 digital input/output pins, all pins have interrupt/pwm/I2C/one-wire supported(except D0) -1 analog input (3.3V max input) -A Micro USB connection

Additional Information:

• Packaging Details: 1 x D1 Mini 2 x Lange Weibliche Pins 2 x Kurze Weibliche Pins 2 x Normal Pins

Product Details:

Description:

ProtoShield is used in conjunction with Arduino Duemilanove.

Used to build a circuit prototype, can be directly soldered components on the board.
Can also be connected through the mini breadboard circuit.
1 reset button, 1 general use button, and 2 LED circuits can be used directly.
5V, GND, and Raw pins are exposed as well.
The mini breadboard has 170 tie points.
SOIC place for IC.
The breadboard sticks on the prototype shield with its self-adhesive backing.

Additional Information:

• Item Code: prototype-shield
• Delivery Time: 8 - 10 days