Electronic Sensors

Product Details:

Specifications:

• Can be used for: liquid water and other liquids with similar viscosity.
• Port size: G1 / 2 " (4 exceptionally thread) : 15 mm diameter approximately.
• Solenoid valve material: Plastic body part, Copper Fittings.
• Filtering feature: removable cleaning filters.
• Backstop function.
• The device is normally closed, means the valve is closed when no voltage is applied.

Available In:

• 12V, 12V 3/4", 24V 1/2", 24V 3/4" 

Product Details:

16-Way TTP229 Capacitive Touch Sensor Module uses TTP229 integrated circuit, making it easy to add capacitive touch input to your project. It features 16 sensitive touch pads that make an ideal replacement for the old fashioned keypads

Technical Specifications:-

• Built-in regulator with external enable / disable option.
• Operating current, @VDD=3V no load.
• At fast mode typical 9.0uA; @VDD=3V.
• operating voltage: The response time about 100mS at fast mode, 200mS at low power mode for TTP224 The response time about 60mS at fast mode, 160mS at low power mode for TTP224N Sensitivity can adjust by the capacitance (0~50pF) outside for each touch pad.
• Provides Fast mode and Low Power mode selection by pad option (LPMB pin).
• Provides direct mode or toggle mode CMOS output or open drain output.
• Active high or active low by pad option (TOG/OD/AHLB pin). Provides 2 output pins TPQ0D, TPQ2D that have no diode protection, active low.
• Have the maximum on time 120sec / 64sec / 16sec / infinite by pad option (MOT1, MOT0 pin); After power-on have about 0.5sec stable-time, during the time do not touch the key pad, and the function is disabled.
• Auto calibration for life, and the re-calibration period is about 4.0sec, when key has not be touched. Application: Wide consumer products; Button key replacement.

Product Details:

The TTP226 is a touch pad detector IC which offers 8 touch key. The touching detection IC is designed for replacing traditional direct button key with diverse pad size. Capacitive touch allows electronics to sense when your finger is within a few millimetres of a surface to simulate a button press just like how the pushbutton works. Capacitive sensing may be used in any place where low to no force human touch sensing is desirable.

Specification:

• On-board TTP226 capacitive touch induction IC
• On-board 8-way level indicator.
• Adjustable output mode, key output mode, longest time and fast/low power output

Product Details:

Description:

• 4 board-level status indicator
• TTP224 capacitive touch sensor IC 4 keys
• The module can set the output mode, the key output mode, the maximum output time and fast / low power selection

Additional Information:

• Item Code: ttp224
• Delivery Time: 8 - 10 days

Product Details:

MLX90614ESF-BAA-000-TU-ND is an infrared thermometer for non-contact temperature measurements. It can use with any microcontroller that can communicate with it through it's I2C interface.

Features:

• Easy to integrate
• Mounted on a breakout board with two types of pins
• 10k Pull up resistors for the I2C interface with optional solder jumpers
• Factory calibrated in temperature range:
  • -40+125°C for sensor temperature
  • -70+380°C for object temperature
• High accuracy of 0.5°C over wide temperature range (+50°C for both) High (medical) accuracy calibration
• Measurement resolution of 0.02°C
• Single and dual zone versions
• SMBus compatible digital interface
• Customizable PWM output for continuousreading
• Different package options for applications and measurements versatility

Applications:

• High precision non-contact temperature measurements
• Automotive blind angle detection
• Multiple zone temperature control – up to 127sensors
• Thermal relay / alert
• Movement detection
• Livestock monitoring
• Body temperature measurement

Additional Information:

• Item Code: GY-906MLX90614ESF
• Delivery Time: 8 - 10 days

Product Details:

Miniature Microwave Motion Sensor is a X-Band Bi-Static Doppler transceiver module. Its built-in Dielectric Resonator Oscillator (DRO) and a pair of Microstrip patch antenna array, make it ideal for OEM usage in motion detection equipment. This module is ideally suitable for false alarms reduction in intruder detectors when work together with Passive Infrared (PIR) sensor. It can also be used for auto-door opening and vehicle speed measurement.

Additional Information:

• Item Code: HB100
• Delivery Time: 8 - 10 days

Product Details:

This is a simple touch sensor module. You can use it to replace a traditional push button. Using the TTP223 touch detector IC It measures the capacitance of a metallic pad. It can detect the change in capacitance when a finger is near it. This is the same technology used in the iPhone touch screen.

This little sensor can "feel" people and metal touch and feedback a high/low voltage level. Even isolated by some cloth and paper, it still can feel the touch. And the sensetivity well decrease as isolation get thick.

Specifications:

• response time max about 60mS at fast mode, 220mS at low power mode @VDD=3V
• Low power consumption
• 2.0cm x 2.0cm twig module
• Power indicator led

Product Details:

NTC thermistor for temperature sensor is one where the thermistor chip is welded with leads by alloy soldering process, then partially treated by glass sealing.
The element has a bead form with good stability, small size and rapid response
Widely used in temperature sensors, electronic thermometers and eternity calendar, temperature compensation,various kinds of household appliances as well as Industrial, medical, environmental protection, weather and food processing equipment etc.

Features:

• Fastest response time and high accuracy
• Better Stability ,as chip is welded with leads by alloy soldering process
• High resistance and mechanical strength
• Small size, lightweight and cheap
• Mass production for high accurate element
• Operation temperature range: -50 to +260 degrees Celsius
• Thermal time constant: less than 5s (In still air)
• Usable in high-temperature and high-moisture environments

Product Details:

The PIR (Passive Infra-Red) Sensor HC-SR501 is a pyroelectric device that detects motion by measuring changes in the infrared levels emitted by surrounding objects. This motion can be detected by checking for a high signal on a single I/O pin.

Module provides an optimized circuit that will detect motion up to 6 metres away and can be used in burglar alarms and access control systems.


The PIR sensor and Fresnel lens are fitted onto the the PCB. This enables the board to be mounted inside a case with the detecting lens protruding outwards, whilst still allowing easy access to the controls inside the case.

Additional Information:

• Item Code: HC-SR501

Product Details:

Ultrasonic ranging module HC - SR04 provides 2cm - 400cm non-contact measurement function, the ranging accuracy can reach to 3mm. The modules includes ultrasonic transmitters, receiver and control circuit. The basic principle of work:

 

• Using IO trigger for at least 10us high level signal,
• The Module automatically sends eight 40 kHz and detect whether there is a pulse signal back.
• IF the signal back, through high level , time of high output IO duration is the time from sending ultrasonic to returning.

Test distance = (high level time×velocity of sound (340M/S) / 2

Wire connecting direct as following:

• 5V Supply
• Trigger Pulse Input
• Echo Pulse Output
• 0V Ground

 

Additional Information:

• Item Code: HC-SR04

Product Details:

This Panel-Mount Digital Timer series can be operated in 4 separate power supplies,ranges from 240 VAC. Output format can be produced to be Volt-free or voltaic-ouput. Batteries of Lithium CR2032 or rechargeable V80H available for option which is for retaining the programing during Timers operating power disconnected. This Digital Timer is accurate to the minute, designed with either or Graphic description. Also ,it provides 15-combination of Daily-Programs which can lead great convenience to users upon choosing the required days in a week for operating the timer.

Additional Information:

• Pay Mode Terms: T/T (Bank Transfer)
• Delivery Time: 2 TO 3 Days

Product Details:

A Magnetic Contact is an electrically controlled switch used for switching a power circuit, similar to a relay. Magnetic contacts give exact position of the door (open/close).

 

Product Details:

The MPX2010 series silicon piezoresistive pressure sensors provide a very ccurate and linear voltage output directly proportional to the applied pressure. These sensors house a single monolithic silicon die with the strain gauge and thin film resistor network integrated. The sensor is laser trimmed for precise span, offset calibration and temperature compensation.

 

FEATURES:

• Temperature Compensated over 0C to +85C
• Ratiometric to Supply Voltage
• Differential and Gauge Options
• Available in Easy-to-Use Tape & Reel

 

Additional Information:

• Item Code: MPX2010

Product Details:

About :

• Metal Detector with speaker and ttl output.

Features And Usage:

• VCC 9v battery
• Logic high out put with common ground.
• Can detect any metal at the range of 1cm to 3cm. you can connect 9v battery to make it handy.

Note: It will not detect coins if it is in the middle of the coil, it may detect if it is close to the coil. it will not detect any type of explosives. 

Product Details:

Modeling simple, elegant, LCD panels inline connections, moisture-resistant, strong anti-interference, applies to refrigerated cabinets, display counters and other needs of temperature measurement and display of various equipment. Submerge probe into fish tank to measure water temperature (Submerge probe only, do not submerge thermometer in water) 

Product Details:

The Sharp Optical Dust Sensor (GP2Y1010AU0F) is especially effective in detecting very fine particles like cigarette smoke, and is commonly used in air purifier systems.

Features:

• Optical air quality sensor, designed to sense dust particles
• Very low current consumption
• Commonly used in air purifier systems
• RoHS Compliant

Product Details:

The proximity switch is a high-frequency oscillation type, which sends a detection signal quickly, without pressure, no pressure, without a spark, to drive the relay or logic gate. It has high sensitivity, fast frequency response, high repeatability, Short, the output power is large, the anti-jamming performance is good, the working stability is reliable, the service life is long and so on. The switch is filled with resin to make it completely closed, and it has the characteristics of vibration resistance, corrosion resistance and waterproofing.

Product Details:

This is an infrared based sensor array which can be used in advanced line following and grid navigation robots. The array has 4 individual sensors placed next to each other. Each sensor has its own digital output and can sense the presence of a line and indicate it with a 5V logic output. On reading the the digital state of the eight sensors, the user can not only detect the line but also get to know how far the center of the robot is from the line. When all sensors sense the line, the robot is on an intersection.

Features:

• Uses 4 sensors for best resolution.
• Great useful in building fast line following and grid navigating robots.
• Comes with easy to use digital outputs that can be connected directly to microcontrollers.
• The array has mounting holes of 3mm diameter for easy mounting 

Specification:

• The working current, try to choose more than 1 a power supply
• The detection distance: 1 mm and 60 cm adjustable, the closer distance performance more stable, white reflection furthest distance

Additional Information:

• Item Code: array-4-way

Product Details:

The module uses 24 high-precision A / D converter chip hx711, is designed for high-precision electronic scale and design, with two analog input channels, the internal programmable gain amplifier integrated multiplier 128.

The input circuit can be configured to provide an electrical bridge the bridge voltage (e.g., pressure, weight) sensor mode.

The input circuit can be configured to provide a bridge voltage electrical bridge (such as pressure, weight) sensor model is an ideal high-precision sampling front-end modules;

• Comprehensive error (% F.S): 0.05
• Sensitivity (mv / v): 1.0  0.1
• Zero output (mv / v):  0.1

Product Details:

Specifications:

• It's a useful tool for gardening.
• Used to measure soil PH, humidity and light.
• “MOIST” key is correspondent to MOIST on the table. 1-3 (red part) indicate watering needed, 4-7 (green part) indicate water suitable, 8-10 (blue part) indicate too wet.Please adjust watering time according to plant species.
• “PH” key is correspondent to PH 8-3.5 on the table. 7 indicate neutral, the lower the value is, the higher the acidity is. Please adjust soil acidity according to plant species.
• “LIGHT” key is 0-2000 lumen. The higher the value is, the stronger the light is. Please determine the need for shade according to plant species.
• Note: prohibit to probe into water directly; Not insert in the soil for a long time to use.

Features:

• The tool plant owners, gardeners can't live without!
• 3 IN 1: Moisture, Light PH meter Soil analyzer meter.
• For outdoor indoor plants, gardens grass lawn.
• Take the guess work out of your daily garden watering light and moisture.
• Save water, energy and keep your plants, lawn, flower in top condition.
• Measures moisture at root level.
• Prevents over and under watering
• Scientifically accurate.
• Easy to use, just insert and read.
• No battery required, simple and convenient to use
• Simply insert the meter into the soil, switch to the setting you want to measure and read the scale.

Product Details:

Bosch has stepped up their game with their new BMP280 sensor, an environmental sensor with temperature, barometric pressure that is the next generation upgrade to the BMP085/BMP180/BMP183. This sensor is great for all sorts of weather sensing and can even be used in both I2C and SPI! This precision sensor from Bosch is the best low-cost, precision sensing solution for measuring barometric pressure with ±1 hPa absolute accuracy, and temperature with ±1.0°C accuracy. Because pressure changes with altitude, and the pressure measurements are so good, you can also use it as an altimeter with ±1 meter accuracy Enhancement of GPS navigation(e.g.time-to-first-fix improvement,dead-reckoning,slope detection) Indoor navigation(floor detection,elevator detection) Outdoor navigation,leisure and sports applications Weather forecast Health care application(e.g. sirometry) Vertical velocity indication(e.g. risk/sink speed)

Additional Information:

• Packaging Details: 1 x GY-BMP280-3.3 High Precision Atmospheric Pressure Sensor Module