ESP8266 Wifi Module

Product Details:

It's a low-footprint, minimal system development board powered by the latest ESP-WROOM-32 module and can be easily inserted into a solderless breadboard. The ESP32-DevKitC contains the entire basic support circuitry for the ESP-WROOM-32, including the USB-UART bridge, reset- and boot-mode buttons, LDO regulator and a micro-USB connector. Every important GPIO is available to the developer.

Features:

• Small volume,easily embeded to other products
• Strong function with support LWIP protocol,Freertos
• Suppporting three modes: AP, STA, and AP+STA
• Supporting Lua program, easily to develop
• Includes CP2102 usb-uart bridge

Product Details:

ESP32 has five strapping pins:

• MTDI
• GPIO0
• GPIO2
• MTDO
• GPIO5  

Software can read the values of these five bits from register ”GPIO_STRAPPING”. During the chip’s system reset (power-on-reset, RTC watchdog reset and brownout reset), the latches of the strapping pins sample the voltage level as strapping bits of ”0” or ”1”, and hold these bits until the chip is powered down or shut down. The strapping bits configure the device’s boot mode, the operating voltage of VDD_SDIO and other initial system settings. Each strapping pin is connected to its internal pull-up/pull-down during the chip reset. Consequently, if a strapping pin is unconnected or the connected external circuit is high-impedance, the internal weak pull-up/pull-down will determine the default input level of the strapping pins. To change the strapping bit values, users can apply the external pull-down/pull-up resistances, or use the host MCU’s GPIOs to control the voltage level of these pins when powering on ESP32. After reset, the strapping pins work as normal-function pins.

Additional Information:

• Item Code: esp8266-esp32-wroom

Product Details:

NodeMCU IoT Module NodeMCU is a IoT Module based on ESP8266 wifi Module. NodeMCU uses Lua Scripting language and is an open source Internet of Things (IoT) platform.Specification of Node-MCU IoT Module

• The Development Kit based on ESP8266, integates GPIO, PWM, IIC, 1-Wire and ADC all in one board.
• Power your developement in the fastest way combinating with NodeMCU Firmware!
• USB-TTL included, plug&play
• 10 GPIO, every GPIO can be PWM, I2C, 1-wire
• PCB antenna

Features of Node-MCU IoT Module:

• Open source IoT Platform
• Easily Programmable
• Low cost & Simple to Implement
• WI-FI enabled

Product Details:

This is WiFi serial transceiver module, based on ESP8266 SoC. This is the ESP-01 VariantThis has an integrated tcp/ip stack ESP8266 is a highly integrated chip designed for the needs of a new connected world. It offers a complete and self-contained Wi-Fi networking solution, allowing it to either host the application or to offload all Wi-Fi networking functions from another application processor. ESP8266 has powerful on-board processing and storage capabilities that allow it to be integrated with the sensors and other application specific devices through its GPIOs with minimal development up-front and minimal loading during runtime. Its high degree of on-chip integration allows for minimal external circuitry, and the entire solution, including front-end module, is designed to occupy minimal PCB area. The Module Comes with a default AT Firmware. Download the AT Documentation ### This module comes with No Support from us as of the Moment. However There are plenty of Resources Online. So Buy This only if you know what you are getting into ###

Additional Information:

• Item Code: ESP8266-01
• Delivery Time: 8 - 10 days

Product Details:

The ESP8266-07 serial WIFI module is a multiple module thanks to its small micoprosessor. ESP8266-07 has several gpio and can be used completely standalone for example a push notification board, temperature monitor, relay WiFi module etc. You can also use it to provide your Arduino with a wireless connection. You can increase the range by the antenna connection.

Description:

• It run LWIP
• 802.11 bgn
• WIFI Direct (P2P),SOFT-AP
• Built-in TCP/IP
• The AT command is perfect,efficient,concise
• Support three modes: AP, STA and AP+STA coexistence mode

Additional Information:

• Item Code: ESP-07
• Delivery Time: 8- 10 days

Product Details:

ESP8285=ESP8266+1M Flash, the bearing high temperature is 125 (the one for ESP8266 is just 85  More important, the code programmed in ESP8266 can be used for ESP8285 intactly.

ESP-M3 is encapsulated by the high performance chip ESP8285, which is equal to ESP8266 chip plus 1M Flash. The chip ESP825 is encapsulated a advanced Tensilica’s L106 32-bit CPU, together with SRAM. ESP825 has the full and complete WiFi fuction, which can used independently and alsoused as a slaver with other Hoster MCU, which can start directly from the out-built Flash. In addition, the built-in high-speed buffer is benefit for the system performance. Especially, ESP8285 can be used as a WiFi adapter by SPI/SDIO and/or I2C/UART interface, when it is applied to the other MCU design.

• Ultra-small size
• Support serial to WiFi
• Wireless transparent transmission
• Long distance transmission with ultra-low power
• Bearing high temperature to 125 ???, compared to the 85??? for ESP8266.

SOC characteristics

• Built-in Tensilica L106 ultra-low power 32-bit CPU, main frequency supports 80MHz and160MHz, and RTOS
• Built-in TCP/IP protocol
• Built-in one-channel 10-bit high precision ADC
• Outboard interface: HSPI, UART, I2C, I2S, IR Remote Controk, PWM, GPIO
• Deep sleep current is 10uA, the cut-off current is smaller than 5uA
• Wake,connect and transmission data package within 2ms
• The consume power is smaller 1.0Mw (DTIM3) when at stand by status
• Built in 1M byte for SPI Flash

WiFi characteristics

• Support 802.11 b/g/n/e/I
• Support Station, Soft AP, Soft AP+STA mode
• Support WiFi Direct (P2P)
• Support CCMP (CBC-MAC, computation mode), TKIP (MIC, RC4), WAPI (SMS4), WEP (RC4), CRC etc., for hardware acceleration.
• P2P finding, P2P GO mode/ GC mode and P2P power manage
• WPA/PA2PSK and WPS
• 802.11 securitycertification: pre-certification and TSN
• Support 802.11n (2.4GHz)
• 802.1h/RFC1042 frame encapsulation
• Support seam less roaming
• Support AT remote update and cloud update (OTA)
• Support Smart Config function (including Android and Ios device)

Module interface

• 2* UART
• 1*ADC
• 1*En
• 1*wakeup pin
• 1*HSPI
• 1*I2C
• 1*I2S
• More than 10*GPIOs

 

Additional Information:

• Item Code: ESP8285-M3

Product Details:

Ra-02 is a wireless transmission module based on SEMTECH SX1278 wireless transceiver. It adopts advanced LoRa spread spectrum technology, with a communication distance of 10,000 meters. It has strong anti-jamming ability and has the function of air-alarm clock-up Consumption. can be covering thousands of people in the neighborhood environment, especially suitable for reading counters, smart home, alarm equipment.

Additional Information:

• Item Code: Ra-02
• Delivery Time: 8-10 Days

Product Details:

Because of the ultra-small size, ESP-M1/ESP-M2 is now very popular for many people. Moreover, this two modules are based on ESP8285 chip. Compared to the previous modules (e.g. ESP-F, ESP-S and ESP-E ), which are based on ESP8266 chip, the differeces are obvious and listed as follows.

• Small size.
• Bearable a higher temperature (about +125  but ESP8266 is just +85
• The original ESP8266 code can be used on this modules (based on ESP8285 DO NOT change any code)
• Support serial transpent transmission
• Support long distance with ultra-low power
• Support a onboard antenna (For  ESP-M1 )

The WiFi module ESP-Mis manufactured by using a high-performance chip ESP8285. This small chip isencapsulated an enhanced Tensilica L106 diamond series 32-bit kennel CPU witha SRAM. Thus, ESP8285 has the complete function Wi-Fi function; it not only canbe applied independently, but can be used as a slaver working with other hostCPU. When ESP8285 is applied as a slaver, it can start from the onboard Flash.The built-in high-speed buffer is not only benefit to improve the systemperformance, but optimize the store system. In addition, ESP8285 can be used asWi-Fi adapter by SPI/SDIO or I2C/UART interface, when it is applied to otherMCU design. The ESP-M module supports the standard IEEE802.11 b/g/n/e/iprotocol and the complete TCP/IP protocol stack. User can use it to add the WiFifunction for the installed devices, and also can be viewed as a independentnetwork controller. Anyway, ESP-M module provides many probabilities with thebest price.

Additional Information:

• Item Code: ESP8285-M1

Product Details:

ESP-M2 is encapsulated by the high performance chip ESP8285, which is equal to ESP8266 chip plus 1M Flash. The chip ESP825 is encapsulated a advanced Tensilicas L106 32-bit CPU, together with SRAM. ESP825 has the full and complete WiFi fuction, which can used independently and alsoused as a slaver with other Hoster MCU, which can start directly from the out-built Flash. In addition, the built-in high-speed buffer is benefit for the system performance. Especially, ESP8285 can be used as a WiFi adapter by SPI/SDIO and/or I2C/UART interface, when it is applied to the other MCU design.

Features

• Ultra-small size
• Support serial to WiFi
• Wireless transparent transmission
• Long distance transmission with ultra-low power
• Support outboard antenna
• Bearing high temperature to 125  compared to the 85 for ESP8266.

Description:
ESP8285=ESP8266+1M Flash, chip feature1) size is ultra-small2) serial to WiFi3) wireless transmission4) long-range ultra-low power consumption5) high temperature, up to 125 ???6) fully compatible with ESP8266, the esp8266 source code can be used for esp8285


SOC Features:

• Built-in Tensilica L106 ultra-low power 32-bit microprocessor, clocked at 80MHz and 160MHz support RTOS
• Built-in TCP / IP protocol stack
• Built-in 1 channel 10 bit precision ADC
• Peripheral Interface HSPI, UART, I2C, I2S, IR Remote Control, PWM, GPIO
• The deep sleep hold current is 10uA and the shutdown current is less than 5uA
• Wake up within 2 ms, connect and pass the packet
• Standby power consumption less than 1.0mW (DTIM3)

Wi-Fi features:

• Supports 802.11 b / g / n / e / i
• Support Station, SoftAP, SoftAP + STA mode
• Support for Wi-Fi Direct (P2P)
• Supports CCMP (CBC-MAC, counter mode), TKIP (MIC, RC4), WAPI (SMS4), WEP
• (RC4), CRC hardware acceleration
• P2P discovery, P2P GO mode / GC mode and P2P power management
• WPA / PA2 PSK and WPS
• 802.11 i security features: pre-authentication and TSN
• Supports 802.11n (2.4 GHz)
• 802.1h / RFC1042 frame encapsulation
• Seamless roaming support
• Support AT remote upgrade and cloud OTA upgrade
• Support for Smart Config features (including Android and iOS devices)

Module peripherals

• 2xUART
• 1xADC
• 1xEn
• 1x wakeup pin
• 1xHSPI
• 1xI2C
• 1xI2S
• Up to 11xGPIOs
• 4M bytes of SPI Flash
• Operating temperature range: -40 ??? -85 ???
• Module size: 12.3mm×20mm

Note:

• Power supply oltage is DC 3.3V
• IO max output current is 12mA
• NRST pin active low, EN enable pin active high RXD to MCUs TXD, TXD to MCUS
• RXD

Application:

• Household appliances
• Smart socket, intelligent light
• Baby monitor
• Sensor Networks
• Security ID tag
• Wireless positioning system beacon
• Home automation
• Mesh network
• IP camera
• Can wear electronic products
• Wireless location awareness
• Industrial Wireless Control

Additional Information:

• Item Code: ESP8285-M2
• Packaging Details: 1pcs ESP-M2 ESP8285 Wifi Module

Product Details:

Basically an ESP8285 module is an ESP8266 Module with additional 1 MB of Flash memory and the ESP8285 can even bear high temperature upto 125 (the one for ESP8266 is just 85. More important, the code programmed in ESP8266 can also be used for ESP8285.

The core processor of the ESP8285 M4 IoT module uses the cost-effective chip ESP8285. The chip integrates an enhanced version of Tensilica''''s L106 Diamond Series 32-bit core processor in a smaller package with on-chip SRAM. The ESP8285 has a full Wi-Fi network capability that can be used independently or as a slave to other host MCUs. When the ESP8285 hosts an application, it can be launched directly from external Flash. The built-in cache helps improve system performance and optimizes the storage system. In addition, the ESP8285 can be used as a Wi-Fi adapter via the SPI/SDIO interface or I2C/UART port for any microcontroller-based design.

The ESP8285 M4 wifi module supports the standard IEEE 802.11 b/g/n/e/i protocol and the full TCP/IP protocol stack. Users can use this module to add networking capabilities to existing devices or to build separate network controllers. The ESP-M4 module provides Zui''''s great utility at low cost, providing unlimited possibilities for Wi-Fi functionality to be embedded in other systems.


The main technical parameters of the module are as follows:

Wi-Fi

• 802.11b: +20 dBm
• 802.11n: +14 dBm
• 802.11b: -91 dbm (11Mbps)
• 802.11n: -72 dbm (MCS7)

 

Hardware

• Wi-Fi mode: Station/SoftAP/SoftAP+Station
• Security Mechanism: WPA/WPA2
• Encryption type: WEP/TKIP/AES
• Upgrade firmware: UART Download/OTA (via network)

Software

• Software development: Non-RTOS/RTOS/Arduino IDE, etc.
• Network protocol: IPv4, TCP/UDP/HTTP/FTP/MQTT
• User configuration: AT+ instruction set / cloud server / androids / ioses APP

Additional Information:

• Item Code: ESP8285-M4

Product Details:

ESP8266 is a highly integrated chip designed for the needs of a new connected world. It offers a complete and self-contained Wi-Fi networking solution, allowing it to either host the application or to offload all Wi-Fi networking functions from another application processor.


ESP8266 has powerful on-board processing and storage capabilities that allow it to be integrated with the sensors and other application specific devices through its GPIOs with minimal development up-front and minimal loading during runtime. Its high degree of on-chip integration allows for minimal external circuitry, and the entire solution, including front-end module, is designed to occupy minimal PCB area.


Features:

• SDIO 2.0, SPI, UART
• 32-pin QFN package
• Integrated RF switch, balun, 24dBm PA, DCXO, and PMU
• Integrated RISC processor, on-chip memory and external memory interfaces
• Integrated MAC/baseband processors
• Quality of Service management
• I2S interface for high fidelity audio applications
• On-chip low-dropout linear regulators for all internal supplies
• Proprietary spurious-free clock generation architecture
• Integrated WEP, TKIP, AES, and WAPI engines

Specifications:

• 802.11 b/g/n
• Wi-Fi Direct (P2P), soft-AP
• Integrated TCP/IP protocol stack
• Integrated TR switch, balun, LNA, power amplifier and matching network
• Integrated PLLs, regulators, DCXO and power management units
• 19.5dBm output power in 802.11b mode
• Power down leakage current of <10uA
• Integrated low power 32-bit CPU could be used as application processor
• SDIO 1.1/2.0, SPI, UART
• STBC, 1×1 MIMO, 2×1 MIMO

Additional Information:

• Item Code: ESP12
• Delivery Time: 8 - 10 days

Product Details:

The ESP8266 is a brand new low-cost WiFi chip from Espressif which allows you to easily connect your project to the Internet of Things with a simple UART AT command interface.

This is the ESP8266 ESP-03 module with software version 0.90 which has an on-board ceramic antenna for improved wireless range and communicates at 115200 baud. The module breaks out all pins of the chip to a 2x7 SMD pin header with 0.2mm pitch. No external circuits are needed.

The ESP8266 supports 802.11 b/g/n networks as Access Point, Station and both at the same time, it's firmware can be updated over a serial connection.

Features:

• WiFi 802.11 b/g/n
• AP, STA, AP+STA modes
• Integrated TCP/IP stack
• Integrated RISC processor
• On-board indicator LEDs: red for power, blue for activity
• Very low power consumption in power down mode (<10uA)
• Standby current < 1mA
• Controlled via UART interface at 115200 baud with a simple set of AT commands
• Only 2 microcontroller pins needed for communication (RXD/TXD)
• Ships with firmware v0.90, firmware can upgraded any time by user

Product Details:

Specification:

• Use CH340G repalce the CP2102. 
• Open-source, Interactive, Programmable, Low cost, Simple, Smart, WI-FI enabled
• Arduino-like hardware IO
• Advanced API for hardware IO, which can dramatically reduce the redundant work for configuring and manipulating hardware.
• Code like arduino, but interactively in Lua script.
• Nodejs style network API
• Event-driven API for network applicaitons,which faciliates developers writing code running on a 5mm*5mm sized MCU in Nodejs style.Greatly speed up your IOT application developing process.
• Lowest cost WI-FI
• Less than $3 WI-FI MCU ESP8266 integrated and esay to prototyping development kit.
• We provide the best platform for IOT application development at the lowest cost.

Product Details:

Summarize:

LC 5V WiFi relay module carried a ESP8266 WiFi module and microcontroller.

It will send the serial port instructions to the cell phone APP and Implementation within the local area network (LAN) for wireless control relay.

Onboard the ESP8266 WIFI module has three work modes: STA (client), AP (hot), the STA + Ap( hot +client), according to the workings of a module to the corresponding choice of WIFI module working mode.Module need before use serial debugging software and USB to TTL module send serial command was carried out on the WIFI module configuration (don''''''''t power outages after configuration is complete, as some of the parameters of WIFI module cannot be saved when the power is cut off), mobile phone and WIFI module after establishing a network connection can use the phone APP control relay.

 

When cell phone equipped with WiFi module sends commands in the following order:

(The default baud rate 115200)

 

• AT+CWMODE=2, namely AP mode is selected;
• AT+RST, reset;
• AT+CIPMUX=1, open multiple connections;
• AT+CIPSERVER=1,8080, configure the TCP server, set the port;
• AT+CIOBAUD=9600 set the baud rate to 9600. (working in relays to control the baud rate 9600)
• AT+CIFSR to view the AP mode IP address, such as: the APIP, "192.168.4.1";
• Cell phone WIFI signal connection name starts with AI-THINKER or ESP8266;
• In the "TCP connection" address and port into the APP, such as 192.168.4.1 and 8080;
• Click on the grey box relays can be controlled ESP8266 5V Wifi Relay

 

 

 

Features:

• On board Module: ESP8266 WIFI Module,can connect 5 client at the same time on the mode of AP 
• Working Method:Mobile phone equipped with Wifi module 
• Mobile phone and wifi module equipped with one router,and control the relay by APP 
• Onboard Relay: 5V,10A/250V AC 10A/30V DC relay
• ESP8266 5V Wifi ESP-01S Relay
• Plus a ESP-01S Module, the intelligent relay module based on ESP-01S WIFI module design, can be used for DIY their own smart switch, you can remotely through the mobile APP control, providing APP and LUA source. Easy to use, easy to use.

 

Transmission distance:

• The open environment, the mobile phone when carrying on the WIFI module maximum transmission distance of 400 m
• When the WiFI module and cell phone carrying on the router at the same time the signal transmission distance in accordance with the router On the weak
• Onboard 5 v, 10 A / 250 v AC 10 A / 30 v DC relay, absorb 100000 times continuously
• Module with diode effusion protection, short response time
• Module baud rate: 9600,8,1,0,0.

 

Applications:

• Home Automation
• Industrial IOT Applications
• Lighting Controls

Additional Information:

• Item Code: esp8266-wifi-relay-board

Product Details:

Specification/Additional Details

• Model Name/NumberESP12
• Frequency Range2.412 - 2.484 GHz
• Operating Temperature-40 to +125 Deg C
• Integrated Low Power32-bit MCU
• Operating Voltage3.3 V
• Network ProtocolIPv4, TCP / UDP / FTP / HTTP

Additional Information:

• Item Code: pcb-for-esp12